Ford S-Max, 06/2015 – 10/2019 | Warning marking kit

Ford S-Max, 06/2015 – 10/2019 | Warning marking kit

SKU: 01150156

Manufacturer	Ford
Type	S-Max
Year of construction	2015/06 - 2019/10
Scope of parts	19 parts
Main category	warning marking kits
Model	S-Max

303,14 €

incl. 19% VAT , plus

Currently out of stock
Delivery time: 10 - 11 Workdays (DE - int. shipments may differ)

Design/Film

Ready-made, tension-free elements for easy self-assembly in design112 quality with rounded corners and no sharp edges on the surfaces. For minimal attack surface and maximum service life.

Red/white: design112 warning marking red/white microprismatic – Oralite 5921M – warning marking red/white in accordance with DIN 30710 for fixed structures – in accordance with RA 2

This item is custom-made according to customer specifications and is therefore excluded from exchange/return.

Information on fit

For technical reasons, there may be slight differences in fit at the transitions of the warning bars over vehicle edges and beads. This is hardly noticeable at a normal viewing distance of 5 m or more, does not impair the warning effect and does not constitute grounds for complaint.

The starting point of the striped pattern may differ slightly from the illustrations. However, this has no relevance for approval and/or safety effectiveness.

We expressly reserve the right to make changes in the interest of technical progress, which may be made without prior notice.

Note on standard areas / interpretation

DIN 30710 dates from 1973 and was last revised in 1990. Modern vehicle designs rarely offer the possibility of professionally applying the rectangular standard areas of 141 x 564 mm required by DIN on both the right and left sides. At that time, the technical means to adapt warning markings to vehicles did not exist, and the necessary reflective area was defined by the standard areas.

According to DIN 30710:1990, certain requirements are specified for the size and placement of warning markings. The standard stipulates a minimum area of eight standard areas for both the front and rear. The size of a standard surface is 141 x 141 mm = 0.02 m². With eight standard surfaces required for the front and rear, this results in a reflective surface of 8 x 0.02 m² = 0.16 m² per side of the vehicle (sum of the right- and left-facing surfaces).

Our warning marking sets meet the area requirements of the standard, as the required area of 0.16 m² per side is always exceeded for both the front and rear of the vehicle. In addition, for safety and design reasons, we also take into account the sides of the vehicle and meet the required area of 0.16 m² per side.

General information:

Microprismatic warning markings are a weatherproof and cleaning agent-resistant product designed for outdoor use on vehicles. They should be applied to solid, flat surfaces.

Attachment to vehicle/surface:

Curved surfaces: The film derives its enormous reflective power from its microprismatic surface. Due to this technology, the film has very limited elasticity and cannot be recommended for complex radii (surface curvature in two directions)! In such cases, bonds that appear to be working may come loose after approximately one to two weeks. There are no concerns for flat and slight curvatures in one direction.

Tension-free bonding: It is therefore essential to ensure tension-free bonding, which can only be guaranteed by using the wet bonding method described below. Dry bonding is likely to result in the aforementioned detachment and tensioning of the film.

Ambient temperature: between 15°C and 30°C

Surface preparation: The surface to be covered must be free of dirt, grease and any other materials that could affect the adhesive strength. We recommend using design112 Surface Cleaner for cleaning. For best results, remove any unevenness such as paint residue, scratches, rust, etc. beforehand. Remove any type plates/model lettering.

The expert method for positioning:

Spray the surface and adhesive side of the film with design112 Magie ApplyProfi adhesive fluid.
After positioning, use a squeegee, for example, to press the fluid out between the surface and the film – do not apply too much pressure. Depending on the temperature and surface, the drying time is approx. 10 minutes. If there are still air bubbles in the surface after application, pierce or cut the air bubbles with a sharp (razor) blade and brush the air out towards the opening.

Remove:

Heat the foil and surface with a hot air gun.
Peel off the film flat along the surface
Remove adhesive residue with isopropyl alcohol or thinner.

Care instructions

For a long service life of your lettering

To ensure that you can enjoy your vehicle lettering/markings for a long time, we kindly ask you to observe the following points:
The adhesive film on vehicles only reaches its final adhesive strength after approx. 48 hours at 15 °C. If the temperature is lower, this period is extended accordingly. You should only wash your vehicle again once the adhesive strength has been fully activated.

Clean the vehicle by hand only – do not use a high-pressure cleaner.
If you decide to use a high-pressure cleaner at your own risk, please note the following:

Only spray the vehicle with cold water.
Keep a minimum distance of 80 cm.
Do not spray directly onto the edges of the film.

Perforated films (e.g. on windows) must not be cleaned with a high-pressure cleaner.

When applying stickers to vehicle windows, you should ensure that windscreen wipers do not run over the design, at least not permanently (as is the case with rear windscreen wipers, for example).

Do not use aggressive or solvent-based cleaners to clean the lettering.

Under no circumstances allow the cleaner to dry on the film or use it in direct sunlight.

The vehicle may be treated with polish at the earliest 3 weeks after the adhesive film has been applied. Only use wax-free polishes containing silicone or Teflon for plastic surfaces.

If the durability of the colour film is not to be impaired and the vehicle is to be excluded from regular cleaning, the vehicle may only be cleaned by hand or driven through a car wash with a textile wash without a hot wax programme (no brush wash). The use of waxes or care products that are not expressly approved for use on films may lead to staining on the film.